🛠️ DIY 55-Gallon Gravity Chicken Feeder
Build a high-capacity gravity feeder using a plastic barrel and poultry feeder ports so you can reduce refills, cut down on waste, and make daily chicken chores easier.
📸 Hero Photo Placeholder
Add a finished photo of the completed 55-gallon feeder here.
⭐ Backyard Chicken Planner Project Rating
Why I Built This Feeder
As a chicken flock grows, daily feeding can become one of the most repetitive chores. Small feeders work fine for a few hens, but larger flocks can empty them quickly, waste feed, or require refilling more often than you would like.
This project uses a plastic barrel and gravity feeder ports to create a larger feeder that can be adapted to different flock sizes. The same basic idea works with a 5-gallon bucket, a 20- or 30-gallon barrel, or a full 55-gallon drum.
I currently use a similar setup with 50-gallon barrels. I do not usually fill mine completely. Instead, I normally add one 50-pound bag of feed at a time to help keep feed fresher and reduce the chance of moisture problems.
Is This Project Right for You?
A 55-gallon chicken feeder is not necessary for every backyard flock. If you only have a few chickens, a smaller bucket feeder may be easier to move, clean, and manage. But if you have a larger flock, want fewer refills, or already have a food-grade barrel available, this project can be a very practical upgrade.
| Flock Size | Recommended Feeder Size |
|---|---|
| 4–8 chickens | 5-gallon bucket feeder |
| 8–20 chickens | 20–30 gallon barrel feeder |
| 20–40 chickens | 30–55 gallon barrel feeder |
| 40+ chickens | 55-gallon barrel feeder |
Materials Needed
- 55-gallon plastic barrel or food-grade drum
- 4–6 poultry feeder ports
- Hole saw sized for your feeder ports
- Drill
- Tape measure
- Marker
- Level
- Silicone sealant, optional
- Stainless screws, if required by your feeder ports
- Concrete blocks, wood stand, or PVC stand, optional
💡 Builder’s Tip
If possible, use a food-grade plastic barrel that previously held food-safe material. Avoid barrels that stored chemicals, cleaners, fuel, pesticides, or unknown liquids.
Tools Needed
| Tool | Purpose |
|---|---|
| Drill | Used with the hole saw to cut openings for the feeder ports. |
| Hole Saw | Creates clean, consistent holes for the feeder ports. |
| Tape Measure | Helps keep feeder ports level and evenly spaced. |
| Marker | Used to mark hole locations before drilling. |
| Level | Helps keep the ports aligned around the barrel. |
| Utility Knife or Deburring Tool | Used to clean rough plastic edges after drilling. |
How Much Feed Will a 55-Gallon Barrel Hold?
A full 55-gallon drum can hold a large amount of chicken feed, but the exact weight depends on the feed type. Pellets, crumbles, mash, and grains all settle differently.
| Container Size | Approximate Feed Capacity | Best For |
|---|---|---|
| 5-gallon bucket | About 25–35 lbs | Small backyard flocks |
| 20-gallon barrel | About 80–120 lbs | Small to medium flocks |
| 30-gallon barrel | About 120–170 lbs | Medium flocks |
| 55-gallon drum | About 220–300 lbs | Large flocks or long refill intervals |
💡 Real-World Feeding Tip
Even though a 55-gallon drum can hold several hundred pounds of feed, I usually only add one 50-pound bag at a time. This helps keep feed fresher, reduces the risk of moisture problems, and makes the feeder easier to move if needed.
How Long Will One 50-Pound Bag Last?
The table below uses a general estimate for adult laying hens. Actual feed use will vary based on breed size, weather, free-ranging, feed waste, age, and overall flock condition.
| Number of Chickens | Approximate Days Per 50 lb Bag |
|---|---|
| 6 chickens | About 30–40 days |
| 10 chickens | About 18–24 days |
| 20 chickens | About 9–12 days |
| 30 chickens | About 6–8 days |
| 50 chickens | About 4–5 days |
For a more personalized estimate, use the Chicken Feed Cost Calculator to estimate monthly feed usage and feed cost based on your actual flock size.
Step-by-Step Build Instructions
Building this gravity feeder is straightforward, but careful measuring and port placement matter. Each step below includes a photo placeholder so you can add real project photos once you complete the build.
🛠 Step 1 — Choose Your Barrel
Choose a clean plastic barrel or drum. A food-grade barrel is best, especially if it previously held food-safe material.
📸 Photo Placeholder
Add a photo of the empty barrel before modification.
- Barrel is clean.
- Lid fits securely.
- Plastic is not cracked or brittle.
- Previous contents were food-safe.
🛠 Step 2 — Mark the Feed Port Locations
Mark each feeder port location around the lower portion of the barrel. Keep the ports evenly spaced and high enough that chickens are not scratching dirt or bedding directly into them.
Most 55-gallon feeder builds use four to six ports, depending on flock size and how many birds need to eat at the same time.
📸 Photo Placeholder
Add a photo showing measured and marked port locations.
- Port locations are evenly spaced.
- All marks are level.
- Ports are low enough for feed flow.
- Ports are high enough to reduce scratching and contamination.
🛠 Step 3 — Drill the Holes
Use the hole saw size recommended by the feeder port manufacturer. Drill slowly and let the tool do the work so the plastic does not crack or grab.
📸 Photo Placeholder
Add a photo of drilling or the completed holes.
- Holes are clean and round.
- Rough edges are removed.
- No cracks around the openings.
- All ports fit before final tightening.
🛠 Step 4 — Install the Feeder Ports
Install each feeder port according to the manufacturer’s instructions. Most feeder ports use a threaded body, gasket, or retaining nut to secure the port to the barrel.
Make sure each port sits firmly against the barrel without overtightening.
📸 Photo Placeholder
Add close-up photos of the feeder ports installed.
- Ports are secure.
- Gaskets are seated properly.
- Ports face outward evenly.
- No visible gaps around the openings.
🛠 Step 5 — Add a Secure Lid and Stand
A tight-fitting lid helps keep rain, rodents, insects, and wild birds out of the feed. Depending on your setup, you may also want to raise the barrel on blocks, wood framing, or a PVC stand.
📸 Photo Placeholder
Add photos of the lid, stand, or barrel placement.
- Lid closes securely.
- Barrel is stable.
- Ports are at a comfortable height for the chickens.
- Feeder is protected from heavy rain when possible.
🛠 Step 6 — Add Feed and Test
Add feed slowly and watch how it settles into the ports. Pellets and crumbles usually work well, but some feed types flow differently.
Although a 55-gallon barrel can hold much more, starting with one 50-pound bag is usually the most practical approach.
📸 Photo Placeholder
Add photos of feed being added and chickens using the finished feeder.
- Feed flows into each port.
- No feed is spilling excessively.
- Chickens can access the ports.
- No rain or moisture is entering the barrel.
Real-World Results
This project is not just about building the largest feeder possible. The real benefit is reducing daily chores, lowering feed waste, and creating a feeder system that can be scaled to your flock size.
| Feature | Result |
|---|---|
| Feed Capacity | Can hold far more than a standard hanging feeder |
| Refill Frequency | Reduced compared to small feeders |
| Best Feed Type | Pellets or crumbles |
| Feed Waste | Low when ports are installed correctly |
| Best Placement | Covered run, coop overhang, or protected feeding area |
| Portability | Low once filled with feed |
Estimated Cost Savings
Large-capacity commercial feeders can be expensive, especially for bigger flocks. Building your own barrel feeder may save money if you already have access to a clean barrel or can find one locally.
| Option | Estimated Cost |
|---|---|
| Commercial large-capacity feeder | $150–$350+ |
| DIY barrel feeder, excluding barrel | $40–$90 |
| DIY barrel feeder, including used barrel | $60–$130 |
| Potential savings | $75–$250+ |
Prices vary depending on feeder ports, barrel availability, hardware, and whether you build a stand.
Advantages of a 55-Gallon Gravity Feeder
- Greatly reduces how often you need to refill feed.
- Works well for medium and large flocks.
- Can be adapted to different barrel or bucket sizes.
- Reduces feed waste compared to open pans or trays.
- Uses simple gravity feed with very few moving parts.
- Can be built less expensively than many commercial large-capacity feeders.
Things to Consider Before Building
- A full 55-gallon feeder can become extremely heavy.
- The barrel needs to stay dry inside.
- It is not ideal for small flocks unless you only add small amounts of feed.
- Feed ports must be installed at the correct height.
- The barrel should be placed where chickens can access it easily without exposing feed to heavy rain.
- If rodents are a problem, additional feed storage and predator control may be needed.
Common Mistakes to Avoid
| Mistake | Why It Matters |
|---|---|
| Installing ports too low | Chickens may scratch bedding, dirt, or moisture into the feeder. |
| Installing ports too high | Smaller chickens may struggle to reach the feed. |
| Using a dirty or unknown barrel | Barrels that held chemicals should never be used for feed. |
| Leaving the feeder exposed to rain | Moisture can cause feed to clump, mold, or spoil. |
| Overfilling the barrel | Feed can sit too long and lose freshness. |
| Skipping a secure lid | Rodents, insects, rain, and wild birds may access the feed. |
Maintenance Tips
- Check the feeder ports weekly for clogs or damp feed.
- Inspect the lid after heavy rain.
- Clean spilled feed around the barrel to discourage rodents.
- Do not allow old feed to sit at the bottom for long periods.
- Periodically empty the barrel completely and wipe out dust or crumbs.
- Move the feeder under cover if rain frequently blows into the ports.
What I Would Do Differently Next Time
If I were building another one, I would pay extra attention to placement before filling the barrel. Once feed is added, a large barrel feeder becomes much harder to move.
I would also consider adding some type of simple rain shield above the feeding ports if the feeder will sit in an exposed area.
📸 Improvement Photo Placeholder
Add photos here later showing any rain shield, stand, or placement improvements.
Frequently Asked Questions
Can I build this feeder using a 5-gallon bucket?
Absolutely. The same gravity feeder ports work well with 5-gallon buckets for smaller backyard flocks. The construction process is nearly identical, with the primary difference being feed capacity.
How many feed ports should I install?
Most builders use four to six feed ports on a 55-gallon barrel. Smaller containers may only need two or three ports depending on flock size.
Can I leave the feeder outside?
Yes, but placing it under a roof, coop overhang, or covered run will help keep feed dry and extend the life of the feeder.
Will chickens waste less feed?
In our experience, gravity feeder ports generally reduce feed waste compared to open pans and trough feeders, especially when installed at the proper height.
Can rodents get into the feeder?
A properly sealed lid greatly reduces the chance of rodents accessing stored feed, although spilled feed around the base should always be cleaned up promptly.
Video Walkthrough
🎥 Video Placeholder
A complete build video will be added after the project is photographed and documented.
Project Gallery
📸 Photo Gallery Placeholder
Finished Project
Side View
Feed Ports
Stand Construction
Inside Barrel
Installation Photos
Recommended Products Used In This Project
| Product | Purpose | Status |
|---|---|---|
| Riverbend Resources Poultry Pro Feed Ports | Gravity Feed Ports | ★★★★★ Personally Recommended |
| 55-Gallon Food Grade Barrel | Feed Storage | Recommended |
| Hole Saw | Installation | Required |
| PVC Stand Materials | Optional Stand | Optional |
Affiliate links will be added to recommended products as they become available.
Related Backyard Chicken Projects
- BCP-002 — DIY 55-Gallon Gravity Chicken Waterer (Coming Soon)
- BCP-003 — Roll-Away Nest Box (Coming Soon)
- BCP-004 — Predator-Proof Coop Door (Coming Soon)
- BCP-005 — PVC Automatic Watering System (Coming Soon)
Helpful Planning Tools
Estimate monthly feed costs based on your flock size.
Open Calculator →Estimate egg production and potential income.
Open Calculator →Estimate the cost of building or buying a coop.
Open Calculator →Plan the ideal flock size for your property.
Open Planner →What Happens Next?
Now that you've built your feeder, the next step is making sure your chickens always have clean water, enough coop space, and an accurate estimate of monthly feed costs. Explore the calculators and upcoming DIY projects to continue building a healthier, more efficient backyard flock.